Kyoritsu 8241 Application Software Installation Manual de usuario descargar pdf

This manual contains instructions how to install the DMM Application for MODEL 8241.

1. Introduction

● Interface

This instrument is equipped with a USB interface.

Specifications of USB : Ver.1.1 (Reference)

Following can be done by USB communication.

・Downloading files in the internal memory of the instrument to a PC.

・Real-time data reception

● Software

DMM Application（supplied CD-ROM）

●

System Requirements

・OS (Operation System) Windows2000 or later (CPU : Pentium 133MHz or higher）

・Memory 64Mbyte or more

・Display 1024 x 768 dots, 65536 colors or more

・HDD (Hard-disk space required) 10Mbyte or more

● Communication Commands

For details on commands, refer to the manual (PDF) in the CD-ROM.

● Trademark

・

Windows

is a registered trademark of Microsoft in the United States.

・

Pentium is a registered trademark of Intel in the United States.

Installation of “DMM Application” Software

(1) Followings shall be checked before installing the software.

・

To prepare your system to install this software, please close

all open

programs.

・ Be sure NOT to connect the main unit DMM with a USB until

install is completed.

・ O n Wi n d o w s X P / Vista, in s t a l l s h a l l b e d o n e w i t h

Administrative right.

(2)

Insert the supplied CD-ROM in your PC’s CD-ROM Drive.

〈For Windows Vista〉

The message “An unidentified program wants access to

your computer” is displayed and then Click “Allow”.

Then, the installer sets up automatically. If it doesn’t run

automatically, double click the “setup.exe”.

Click “Next” when following window appears.

(3) Click “Next” after entering the user information and

specifying an install destination.

(4) Confirm the information on install, and then click “Install”

to start installing.

(5)

Install is completed when the wizard finishes. Click “Finish”.

How to un-install the PC Software:

Click the “Control Panel” in the Start Menu at the lower left on the Windows screen, and then click the “Add

or remove program (for Vista “Programs and Features”) tool to select and delete the “DMM Application”.

3. USB Driver Installation

3-1 USB Driver Installation

(1) Connect one end of a USB cord to your PC.

(2) After connecting them properly, following balloon (window) appears and

install starts.

〈For Windows Vista〉

When effectively setting of user’s account Control, your Permission to

continue is requested.

Click “Continue”.

・

A balloon (window) shown below appears after following

steps (3) and (4) complete. Step (3) and (4) will be

repeated twice.

(3)

Click “Install the software automatically (recommended)”,

and insert the “DMM Application” CD-ROM in your PC’s

CD-ROM drive.

Then click “Next”.

〈Example : Windows XP〉

In case th at f ollow ing window appea rs, click

“Continue anyway”. (It is an operation check, and no

problem happens if install is continued.)

〈For Windows Vista〉

The message “Windows can’t verify the publisher of

this driver software”is displayed and then Click the

message “Install this driver software anyway”.

(4) Install is completed when the wizard finishes. Click

“Finish”.

3-2 USB Driver Un-installation

When install of the USB driver is interrupted and

reinstall cannot be done, follow the procedure below

and delete the existing driver, and then install it

again.

(1) Connect a PC and the instrument with a USB

cord.

(2) Click the “Control Panel” in the Start menu.

(3) Click “System” in the Control panel.

(4) Then click “Device Manager”.

(5) Right click on “MODEL 8241” in the USB

Controller.

(6) Click “Uninstall” to uninstall the USB driver.

(7) Remove the USB cord connecting your PC and

the instrument once, and connect them again.

(8) When “Found New Hardware Wizard” window appears, follow the procedures described at “USB

Driver Installation” and install the driver.

3-3 COM Port Number

Click the “System” on the “Control Panel”, and then

click on the “Hardware” tab. Then select the “Device

Manager” and click the “+” mark next to “Port (COM

and LPT)” to show a list and confirm the COM Port

number assigned to MODE 8241.

3-4 Changing the COM Port No

Right-click on the “MODEL 8241” and click “Properties”, and

click on the “Port Settings” tab. Then, select “Advanced…”.

Select any number (COM1 to COM16) for COM Port

Number, and then click “OK”.

4. Start of “DMM Application”

Start the software by; 1) clicking the icon for “DMM

Application” on the desktop, or 2) clicking “Start”

“Program”

“

KEW”

“DMM Application”.

Then the Main Window for the “DMM Application”

appears. Select the COM Port No.

Clicking “File” and then “Exit” or “x” box at the

upper right of the window quits the program.

MODEL 8241

Application Software

Installation instructions

8-08 92-1982

Instruction

Manual

MODEL 8241 1

Indice de contenidos

Pagina 1 - MODEL 8241

This manual contains instructions how to install the DMM Application for MODEL 8241.1. Introduction● Interface This instrument is equipped with a US

Comentarios a estos manuales

Sin comentarios

Kyoritsu 8241 Application Software Installation Manual de usuario

Busca en linea o descarga Manual de usuario para Herramientas Kyoritsu 8241 Application Software Installation. KYORITSU 8241 Application Software Installation User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Herramientas Kyoritsu 8241 Application Software Installation